Archive for October, 2011

How To Repair Vinyl Seat – Look Good and Adequate

How to restore the vinyl seats will probably be your easiest solution when it comes to repairing vinyl. There are people who work with a little “, but in general, the seat is easier to recover, there is more padding in the field of repair, the patch can be used to strengthen the repair, which just seems to me less suitable and easier to repair. Repair vinyl, of course , a game of skill balanced with patience. Taking the time to do the repairs you do not just look good and adequate, and will make or break repair vinyl master.

One thing is for sure to remember when a large hole or crack, then it must be replaced, not repaired. I’ve seen a lot of space on holidays and refused to work a lot, because I know my limits my fairy dust, because some of my clients over the phone (which is one reason I love my job so much because I use this product properly as if by magic). If the seat has a hole in it to say, 3 or 4 inches, maybe more, but it depends on the structure below, the seat should go to the store. What is a fair improvement repairs, products that are available for small defects do not blow that if they could not be worse. But damn they can make a new piece of vinyl new look and improvements will last longer when you’re done.

I find that a good relationship with a good shop should be in the coatings business. If you think that is evil, and repair of vinyl just does not cut, so always refer to the customer a good upholstery shop. Not only be happier with the end result, but you will. Build relationships with upholstery shop, you’ll also get a way more in automotive interior restoration. A good shop will have the padding to make them work for them for their clients, according to just go ahead.

In this business is that you know, you know, and how well they can perform.

Always prepare to leave the decision at the time of preparation, use a Scotch Brite pad wear, such as cleaning. Sand the area, if possible with 240 sandpaper, sand, usually about an inch around the area, giving the area around the hole a little “more than a connection to make. Wipe again.

Apply a thin layer of primer or base is taken over the area by wiping with a damp paper towel vinyl repair. It gives you prepare for the dye to be applied, and gives you a chance to bond a little “more.

Now, a little “on vinyl cold or heat if only a little harsh on the hair dryer, be careful not to burn support, if any is left, thus helping in the patch does not have to put in

If you need to add the patch now. I want to cut the patch in order to meet about 1 / 4 inch from all over the inside edge of the patch is cut, so that the corners are rounded. Slide under the repair patch with sharp tweezers. Get the patch to finish in the bond when it is heated close to the vinyl helps to give added strength to the patch below. If you use glue carefully, boiling, I do not like the repair adhesive vinyl in a chair … door panel, now that’s another story. Glue, Super Glue can also help to restore the vinyl door panels or sediment, and in place, you have to bend, and I still have to use super glue, which does not leave lasting stains.

After the patch in place, if necessary, it is time to put vinyl repair compound. There are so many different brands to choose from, thick, thin, and the list is quite long. I use a pen to high temperatures and low heat Gator compounds. Good deeds, and seeds, and hard. But we all have our favorites are still in search mode, always looking for new and better ways to improve and get the perfect vinyl repair. So if you have any suggestions, please put them in the comments.

Subtle mixture along slit with a knife, palette, and the area under the under the cover of the patch, if used, then smooth the top. Now the first layer should be thick, a little “, but smooth, you do not want the ball, but a significant amount to cover the area, filling the gap, and only takes a broad mix of about 1 / 4″. Smoothing with your fingers, if necessary.

Use of our wheat, which was held in the palm of your hand, not your finger that you do not want to leave a dent during heating vinyl, vinyl heat with heat gun until the mixture becomes colorless and repairs can see the smoke, that’s what you want from the two to blend together as quickly as smoke (and fire roads, you do not want to burn just melted) to remove heat and immediately press the pad to the field of grain vinyl repair. It will be quite hot, sometimes I put a towel in hand with wheat ground, burn injuries are not part of the fun to work all day. If you can make the grain shape you make them “a little thicker and helps reduce hand burns. Wait there for a few seconds, then exhale Press firmly,. But it is not strong enough to expand the heated vinyl. Practice makes perfect. .. .

Dye the area with a thin layer of dry vinyl using water-based dye, I turned on my air rifle, to help you dry your hands. Now apply another layer of connection repair, remember, a thin layer of fine, to keep their jobs as small as possible, your efforts to improve the vinyl disappear as little as possible. Heat the area again, then press the pad in place of wheat, field Dye and see what you have …. need more structure, or both, was the judge. If more than one connection, so it is necessary to keep it going. Of the compound layer in thin layers until cracks appear as smooth as possible. The fact is, repairs to merge back into the chair. Maybe a little “more than a color, or even remove the main lever on the board to fill the repair vinyl repair If you need a network can be used,. But I really do not like. After applying to the fabric, it is difficult to make look really natural. If You know how you can achieve with your color textured vinyl. But with grit sand pad is the best way to achieve perfection in the repair of vinyl. Vinyl repair work and not let it work.

There is a point performances. If your area is growing, and improvements so it seems …. Simply put, no, stop and take a step back, take a break and see what you need to do. If there is anything he can do it better, then do it. But do not settle for the improvements that are not perfect, so expect to pay for this service if you are right, it will not boot, it’s that simple. We all want perfection, and not all the seats repaired. We are craftsmen, not magicians.

Vinyl repair skill and takes practice to get it right. So, if you know your limit and need to be replaced, contact the upholstery shop. If you need to repair vinyl, then by all means to be a manufacturer of vinyl repair repairs vinyl and provides the perfect perennial.

Vinyl Repair – How to fix the vinyl seat is just beginning to repair the item out on vinyl. There are many other applications that can not be put in one place, so stay and see what else will come and be sure to shoot me some comments about this I would love to hear feedback.

Tags: , , , ,

Leather Seats – How To Restore Order To Look Good and Comfortable

There are different types of leather car upholstery repairs, all with different situations and applications. There are holes, scratches, gouges, cuts, scratches, worn or cracked, and the bottom right just looking shabby leather seats. I think my all, and in this article we will talk about how to repair a small hole in a thin skin of the back seat, for those of you who do not know what is good to lean on the chair.

Now, when I say it may take a little break for 1 1 / 2 “to 2″ may be a bit “more, but can not push, if you must go to the store to insert padding is better than bad skin repair look at it, maybe will not take in any case. When in doubt, include it.

Preparation of the chair the key to success in any type of leather repair, leather dye, and solid work. So, lean back all the training, and as long as you only have to clean the whole house, why not, but you do not have a solution in preparation to remove all grease, dirt and grime. You must clean the surface and well prepared for work. When I cook, I use a solution of alcohol, acetone, ammonia, and a small amount of TSP substitute, with water in a spray bottle. Spray the seat with a solution and stain with a piece of Scotch Brite scuffed leather seats for the entries in the color of the skin and remove dirt on the seat, and then wipe with a clean lint-free cloth. Once clean, apply a primer respect the basic seat, I usually dye in most cases, lean, when I do a repair or any seats, but sometimes it does not need not need to fill all space, but the place is clean and good, which reduces the amount of dye into the in the skin and the end result will be renovated premium leather.

Now for the holes. We say that V-shape, for example. How, where you gott’n chair with something in his back pocket, oh! I know that feeling, in college I had a 1986 Mustang SVO, the car is very rare and beautiful (man I miss that car) and I went out to go to class with a pen in his pocket and pulled back to V-shape “to 2 chair, I gave up on it, and, of course, when I knew nothing about skin repair. But now I do, and here it is.

Sand the area around the crack with 240 sandpaper, to give “greater mixture over low heat button. Underpatch Take a sheet of material and slides under the water patch under the eye with a brace, allowing about 1 / 2″ smaller in all the way around. I usually cut my patches into a circular shape, which makes it a bit “easier to slide down you can use a different patch below, I, as a species. Coated on one side of the heat activated adhesive.

Now, take a drop of glue on the skin and apply a thin layer at the bottom of the patch to repair the skin. If the skin is installed correctly, and then a good game, but sometimes not. In this case we can use a combination of leather and glue to the improvements made by a small amount and smooth over the patch then lay skin side down. The distribution of small amounts of boiling mixture over the entire area and smooth with a palette knife, do not forget to keep the area as small as possible, the lower the better. Now heat the area with your hair dryer, heat gun to keep from repairing the skin and slowly move into the repair area, will give you less control “a little more heat, do not want to burn and reduce the skin. The idea is to treat the mixture and make it stick to the the skin before cooking, skill, practice makes perfect. After the mixture is cured at once, click the site in the palm of wheat improvement, do not press hard, but firm.

At this time, use a damp paper towel, use little improved adhesion to substrates and painting with dye color skin with water. Dry thin layer of dye, but not wet. Then again apply and smooth out another thin layer of material. Heat again, and grains, dyes have an idea what you do increase the repair. Thin layer of paste is applied and cured then updated, much better than one thick layer. Once you have built and looks good, you repair the blend in the remaining seats, if necessary, by applying a thin layer of skin pigment to complete. Drying hands the same color, hair dryer, and a big tip rub dye into the skin with your hands to force the dye into the folds of skin helps tons, do not be afraid to get their hands dirty. But I said, I’m allergic to latex gloves, bites, so I came home every day to dye your whole hand, it’s a pain, but I want to work and look better with love “rubbing their tiny leather upholstery repair. After the dye cured, apply top coat of satin or matte coating on the light-skinned mixed with a little slip additives’ added to the soft touch. The chair is completely dry, then apply a leather conditioner to finish and make room for the juice they need, and I feel great and look for you.

Now there are many other options are correct, sometimes I have to use air dry leather repair compound over the mixture over low heat to soften the skin repair. Sanding with 400 grit paper until it looks good. You also can give your air gun to draw a drop of just around the corner to give it a textured, drying between coats. Fabrics can be used, but if you do it right the gun works great effect. When I do a repair of the skin, I do not give up until it looks perfect. Patience is a virtue, right. You will not get in a hurry, it’s only to be disappointed again and then you really have a problem.

Ship repair skin and professions. The use of dyes and compounds that have high quality and are made to the end. Provide a place for skin repair, and the comfort of knowing you have improved on the skin that will last and look great for years to come.

I hope that this is to help you in the coming months there will be more articles like this, but in different situations, repair skin, as I said in the first place. There are many different ways in which leather seats may be damaged, we spent much time in our cars and good “sh $ $ that happens”, right.

Tags: , , , ,

Car Lifts, Truck Lifts, Automotive Lifts & Motorcycle Lifts – How to Choose the Best Type For the Job

Automotive lifts, including car lifts, truck lifts, or motorcycle lifts, are a vital piece of equipment in any garage. In fact, you can get one for your home garage or commercial repair shop to raise almost anything with wheels, in almost any configuration, but you’ll need to choose wisely. Each model is designed specifically to hold a certain type of vehicle, and if you ignore this fact, it can be dangerous or even deadly.

Before you choose one, take some time to get familiar with the many different types of hoists and their features. This will make it easy for you to find the one that works the best for the job you have in mind and keep you safe at the same time.

Types Of Car Lifts, Automotive Lifts, Truck Lifts & Motorcycle Lifts

The type of auto lift you need will depend on the vehicle you’ll be working on, how often you’ll use it, where you’ll be using it, and how much space you have available. Once you know that, you can match your needs to one of the available types, which include:

  • Mechanical Styles — Also called a manual jack, this style raises and lowers with the use of a pedal, handle, pins, screws, or bolts. They are often found in smaller hoists including motorcycle and utility lifts. o Hydraulic Automotive Lifts — This method compresses a special liquid and uses a pump to force it through cylinders. This gives it added safety while making them easy to use.
  • Electric/Hydraulic Truck & Car Lifts — This style has added stability and security while ensuring the entire system works quickly and smoothly.
  • In Ground or Pit Models — Best used when space is at a premium and you need convenience, this style sits into the floor allowing you to drive the vehicles on and off. They run on hydraulics or electric/hydraulic systems, so they’re easy, fast and can move a decent amount of weight.
  • Portable Automotive Lifts — If you travel frequently and need something you can take with you, these smaller versions are hassle-free regardless of the style you choose. o Air Powered Models — Generally reserved for motorcycle lifts and small utility/recreational vehicle lifts, you simply have to hook this style up to an air compressor to raise and lower the hoist.

Features Of Each Type Of Car Lift, Automotive Lift, Truck Lift & Motorcycle Lift
Once you know what type of car lifts will work best for you, take a closer look at the details to decide which one would be the best purchase. Automotive lifts for trucks and cars come in several main styles:

  • Two Post Car Lifts — Great for home garages, this style takes up very little space and comes in two different styles: Symmetrical, which has two posts across from each other to center the weight (better for vehicles heavier in the rear), and asymmetrical, which holds the weight toward the front leaving room to access the interior of the vehicle.
  • Four Posts Models — With a sturdier build, the four post style remains stable even under a heavier load and make it easy for you to drive the vehicles directly onto it.
  • Scissor Styles — While unsuitable for permanent storage, they are ideal for a home garage. Both professionals and avid diyers prefer this style for the increased access to the undercarriage and the ability to hold larger vehicles like buses.
  • Low-Rise Models– These have a dropped crossbar and low profile to prevent body damage and give you the room you need to work.
  • Pit Hoists– Whether you have a pit or want to save space, pit style automotive lifts make quick lube and tire rotation a breeze. With no cross bar, you have plenty of room to work. Portable or permanent mount, you decide.

When you need to store a vehicle, you need a model with stable and secure construction. Two automotive lifts that are ideal for storage include:

  • Single Post Car Lifts — Suitable for cars, trucks, boats, and recreational vehicles, this style’s single-armed, wide platform is mounted for long-lasting stability.
  • Two Post Car Lifts — With no anchoring or mounting, you can double your storage wherever there’s a concrete floor. The sturdy platform safely holds vehicles and keeps the entire undercarriage protected.

Larger vehicles like tour buses are tough, but they still require maintenance. Therefore, you’ll need a heavy-duty mobile column truck lift that can handle the weight and give you enough clearance to work comfortably. These easily lift approximately 64,000 pounds in as little as a minute and have added security, locks, and stabilization.

If you’ll be doing a lot of alignments, consider a two post, four post, or scissor alignment lift with an open front and clear center. Lawn maintenance and utility vehicles require a special turf equipment lift that will give you space and be fully adjustable to fit almost anything you can park on it.

Motorcycle lifts are available in several different styles, but use very little space and are very portable. While some use a pedal, others are air powered, or use a combination of electricity and hydraulics to raise the platforms.

Automotive lifts come in all different configurations, and choosing the right one will make a world of difference when it comes to actually doing the repairs. Simply match the right piece of equipment to the right job and you’ll discover just how quick and easy repairs can be.

Tags: , , , ,